Some years ago I built a geodesic dome out of ½ inch galvanized steel electrical conduit, to serve as an aviary for chickens and small parrots. I wrote a computer program to calculate the proper lengths of steel tubing, and draw the diagram shown below:
The dome is made from three different lengths of tubing. I used colored stickers on the tubes to mark the different lengths -- red for the long ones, violet for the medium lengths, and green for the short ones. You can see those colors in the drawing.
The ends of the tubes are smashed flat with a hammer, and then holes are drilled in the flat ends for a bolt to go through to connect up to six of the tubes together. Aviary wire is then wrapped around the dome to keep the birds in and predators out. The completed dome is 18 feet high, and over 20 feet in diameter.
For this project, something a little more modest in size is required. Something less than three feet in diameter, so it can fit through a door.
For the first attempt at a smaller dome, I used bamboo kebab skewers and gumdrops. The three lengths of the struts are 100%, 97.85%, and 84.53%. Because I knew I would be using soda straw for the more permanent second version, and the straws were 7¾ inches long, I chose that length for the long (100%) strut. That made the other lengths 7½ inches, and 6½ inches.
You will need these materials for the gumdrop dome:
- 90 skewers 7¾ inches long
- 85 skewers 7½ inches long
- 80 skewers 6½ inches long
- 11 green gumdrops
- 15 orange gumdrops
- 50 red gumdrops
- Cellophane tape
With the sticks all cut to the proper lengths (using a pair of wire cutters) the first step is to make the central pentagon of the dome. Five short sticks are stuck into a green gumdrop, and a red gumdrop is stuck onto each of the five ends of the sticks.
Next, five medium sticks are stuck into the red gumdrops, and the pentagon is no longer flat. We can now see that by making the sticks different lengths, we can ensure that the proper three-dimensional form will take shape.
The dome is made of pentagons and hexagons. Each of the five sides of the pentagon has a hexagon attached to it made from the longest sticks. The sides of the pentagons and hexagons are all made of the medium sticks. In the gumdrop dome we have green gumdrops at the center of the pentagons, and orange gumdrops at the center of the hexagons, and red gumdrops everywhere else.
When five hexagons have been attached to the central pentagon, and five more green gumdrops connected at the bottom between the hexagons, we have a structure that looks like a dome.
This is about as far as we can go with gumdrops alone. At this stage, all of the weight of the dome is being held up by the stickiness of the bottom gumdrops. But gumdrops can only hold a small amount of weight before the sticks start to pull out.
We solve this problem by using cellophane tape to hold the sticks together. We only need to do it for the red and orange gumdrops, where we can easily connect the sticks in pairs, across the gumdrops. Attach one end of a 4 inch length of tape to one stick, lay the tape over the gumdrop onto the opposite stick, and then fold the edges of the tape around the stick so the sticky sides hold together. You can see this in the photo below.
We end up with a nice dome. But it won't hold up well to being moved around, because the gumdrops are heavy and don't hold the sticks well enough. But it let us get the concept, and it was nicely color coded.
Our second, more portable and permanent dome, is made from plastic soda straws and small brads, the kind used for fastening paper.
You will need these materials for the soda straw dome:
- 90 straws 7¾ inches long
- 85 straws 7½ inches long
- 80 straws 6½ inches long
- 76 small brads
The first step is to cut all the straws to length.
Next, poke holes a quarter of an inch from each end of each straw with a sharp knife or an ice pick.
Next, make 6 five-sided stars (from the short straws), and 15 six-sided stars (from the longest straws) by sticking the brad through the ends of 5 (or 6) straws, and bending the ends of the brad over to secure them.
We begin assembling the dome by connecting one side of the center pentagon to one side of a hexagon. The photo shows one hexagon for clarity, but you will be putting two hexagons on at a time, so there are always six straws meeting at each brad. The photo also only shows one medium length straw forming an edge, but you will be adding the edges on all sides, closing the brad whenever you have six straws connected.
In the photo below, we have five hexagons connected to the central pentagon, and five more pentagons (without sides yet) connected between the hexagons.
The finished dome is 2 feet 2¾ inches tall (68 centimeters). It is lightweight, and can be tossed around without breaking, and will fit through doors, or in the back of a station wagon. The geometry of the finished sculpture is quite beautiful.
The large dome is still housing chickens out in my backyard. It is amazingly strong -- I had to climb all over it to wrap the aviary wire on it, and it never budged.
We put a small plastic shed (7 feet high, 6 feet long, 8 feet wide) next to it, and removed three struts to form a door, and screwed the aviary wire to the shed, so the shed forms a nice door and "airlock" so the chickens don't escape.
A large plastic tarp attached with bungee cords forms a waterproof roof. The small parrots live in the top half of the dome, and the chickens have the bottom half.